Monel
Introduction
Monel Pipe, Monel 400, Wholesale Supplier of Monel Products, Monel k500, Manufacturer of Monel Products in India.
Monel Suppliers, Monel Metal, Monel 400 Suppliers, Wholesale Trader of Monel Products, Monel Material Trader In Mumbai, India.
Newzel Industries is a Manufacturer and Supplier of Grade 400 and K500 Products which include Monel Flanges, Pipe Fittings, Pipes, and Tubes, Newzel Industries supply their products to various International Countries USA, UK, UAE, and Many European Countries in the list.
About Monel
Monel Alloys are nickel-copper alloy that is very strong and doesn’t corrode in sea water, hydrofluoric acid, sulfuric acid, or alkalies, among other things. Used for marine engineering, equipment for processing chemicals and hydrocarbons, valves, pumps, shafts, fittings, fasteners, heat exchangers, and other things.
Properties of Monel
Monel is a single-phase, solid-solution binary alloy that has good mechanical properties even when it is below zero degrees Fahrenheit. Monel alloy 400 has a Poisson ratio of 0.32 and a specific gravity of 8.80. It can melt between 1300 and 1350 °C. The properties of Monel Alloy 400 material at room temperature are shown in the table below.
|
Form |
Condition |
Tensile Strength (ksi) |
Yield Strength (ksi) |
% Elongation |
Brinell hardness |
Rockwell B Hardness |
Tensile Strength (Mpa) |
Yield Strength (Mpa) |
|
Rod and Bar |
Annealed |
75-90 |
25-50 |
60-35 |
110-149 |
60-80 |
517-620 |
172-345 |
|
Rod and Bar |
Hot-Finished (except Hexagons over 2 1/8 inches and Angles) |
80-110 |
40-100 |
60-30 |
140-241 |
75-100 |
552-758 |
276-690 |
|
Rod and Bar |
Hot-Finished Hexagons over 2 1/8 inches and Angles |
75-100 |
30-55 |
50-30 |
130-184 |
72-90 |
517-690 |
207-379 |
|
Rod and Bar |
Cold-Drawn, Stress-Relieved |
84-120 |
55-100 |
40-22 |
160-225 |
85-20C |
579-827 |
379-690 |
|
Plate |
Hot Rolled |
75-95 |
40-75 |
45-30 |
125-215 |
70-96 |
517-655 |
276-517 |
|
Plate |
Hot Rolled, Annealed |
70-85 |
28-50 |
50-35 |
110-140 |
60-76 |
482-586 |
193-345 |
|
Sheet |
Annealed |
70-85 |
30-45 |
45-35 |
65-80 |
482-586 |
207-310 |
|
|
Sheet |
Cold Rolled, hard |
100-120 |
90-110 |
15-02 |
Min. 93 |
690-827 |
621-758 |
|
|
Cold Rolled Strip |
Annealed |
70-85 |
25-45 |
55-35 |
Max. 68 |
482-586 |
172-310 |
|
|
Cold Rolled Strip |
Spring Temper |
100-140 |
90-130 |
15-02 |
Min. 98 |
690-965 |
621-896 |
|
|
Seamless pipe and tube |
Cold Drawn, Annealed |
70-85 |
25-45 |
50-35 |
Max 75 |
482-586 |
172-310 |
|
|
Seamless pipe and tube |
Cold Drawn, Stress Relieved |
100-140 |
55-100 |
35-15 |
85-100 |
586-827 |
379-690 |
|
|
Cold Drawn Wire |
Annealed |
70-95 |
30-55 |
45-25 |
482-655 |
207-379 |
Mechanical properties of Monel alloy 400 at room temperature
Machinability – As Monel gets harder as it is worked on, it is very hard to machine. The same methods that are used to work with iron can also be used to work with Monel.
Welding – The best ways to weld Monel are with gas-arc welding, gas-metal-arc welding, metal-arc welding, and submerged-arc welding.
Forging – Monel can be forged, but only when certain conditions are met.
Hot Working – 648-1176°C (1200-2150°F) is the typical hot working temperature range for monel alloy. It is necessary to choose the ideal temperature before beginning heated work.
Grades of Monel
|
Monel Grade/Trade Name |
ASTM/AISI Alloy Type |
UNS No. |
%Ni |
%Cu |
%Fe |
%Mn |
%Al |
%Ti |
%Si |
|
Monel 400 |
B 127/ B 164 |
N04400 |
Min. 63 |
28-34 |
Max 2.5 |
Max 2.0 |
|
|
Max 0.5 |
|
Monel 401 |
|
N04401 |
Min. 63 |
28-34 |
Max 2.5 |
Max 2.0 |
|
|
Max 0.5 |
|
Monel 404 |
|
N04404 |
52-57 |
Remaining |
Max 0.5 |
Max 0.1 |
Max 0.05 |
|
Max 0.1 |
|
Monel 405 |
B 164 |
N04405 |
Min. 63 |
28-34 |
Max 2.5 |
Max 2.0 |
|
|
Max 0.5 |
|
Monel K500 |
B 865 |
N05500 |
Min. 63 |
27-33 |
Max 2.0 |
Max 1.5 |
2.3-3.15 |
0.35-0.85 |
Max 0.5 |
